-
20%容量电压-20% capacity voltage
电池容量为20%时,单串电池电压,此值用来调整容量偏差Cell battery voltage when the battery capacity is 20%, this value is used to adjust the capacity deviation备案号 : 粤ICP备18161347号...
-
40%容量电压-40% capacity voltage
电池容量为40%时,单串电池电压,此值用来调整容量偏差Cell battery voltage when the battery capacity is 40%, this value is used to adjust the capacity deviation备案号 : 粤ICP备18161347号...
-
60%容量电压-60% capacity voltage
电池容量为60%时,单串电池电压,此值用来调整容量偏差Cell battery voltage when the battery capacity is 60%, this value is used to adjust the capacity deviation备案号 : 粤ICP备18161347号...
-
80%容量电压-80% capacity voltage
电池容量为80%时,单串电池电压,此值用来调整容量偏差Cell battery voltage when the battery capacity is 80%, this value is used to adjust the capacity deviation备案号 : 粤ICP备18161347号...
-
放电过流延时-Discharging overcurrent delay
电池组在放电时,放电电流超过放电过流保护值且达到放电过流延时时间,保护板关断放电开关,停止放电,以防止超功率使用When the battery pack is discharged, the discharge current exceeds the discharge overcu...
-
放电过流释放时间-Discharge overcurrent release time
发生放电过流保护后,到达放电过流释放时间后,保护板重新打开放电开关After the discharge overcurrent protection occurs, the BMS re-opens the discharge switch after reaching the discharge overcurrent ...
-
放电过流保护-Discharge overcurrent protection
电池组在放电时,放电电流超过放电过流保护值且达到放电过流延时时间,保护板关断放电开关,停止放电,以防止超功率使用When the battery pack is discharged, the discharge current exceeds the discharge overcu...
-
自放电率-Self-discharge rate
保护板在工作时,自身耗电量,休眠时不进行计算When the BMS is working, it consumes power and does not calculate when sleeping.备案号 : 粤ICP备18161347号...
-
单体截止电压-Cell cut-off voltage
单体截止电压为所有电池平均电压,当平均电压到达单体截止电压时,保护板判定电池放空,电量为0The cell cut-off voltage is the average voltage of all the batteries. When the average voltage reaches the ce...
-
单体充满电压-Cell full voltage
单体充满电压为所有电池平均电压,当平均电压到达单体充满电压时,保护板判定电池充满电,电量为100%,一般该电压比充电器平均单串电压低0.05v-0.1vThe cell full-charge voltage is the average voltage of all th...
-
循环容量-Cycle capacity
循环容量为电池在做一次充放电循环的容量,一般为电池标称容量的80%The cycle capacity is the capacity of the battery to perform a charge and discharge cycle, generally 80% of the battery's nominal ca...
-
循环次数-Cycle times
循环次数为电池使用的循环次数统计,当充放电电量达到循环容量时,循环次数加1The number of cycles is the number of cycles used by the battery. When the charge and discharge capacity reaches the cycle ca...
-
均衡精度-Balance accuracy
当单串电池间的电压差达到均衡精度电压时,保护板才能开启均衡,一般建议充置为0.02-0.03VWhen the voltage difference between a cell of batteries reaches the equilibrium precision voltage, the BMS can ...
-
均衡开启电压-Balanced turn-on voltage
当单串电池电压高于均衡开启电压时,保护板才能开启均衡When the cell battery voltage is higher than the equalization turn-on voltage, the BMS can turn on the equalization.备案号 : 粤ICP备1816...
-
温度检测-Temperature check
开启温度检测功能,达到温度保护条件时,保护板发过相应保护Turn on the temperature detection function, the BMS is protected when the temperature protection condition is reached.备案号 : 粤ICP...
-
充电均衡-Charging balance
选中为充电均衡,非选中为静态均衡,充电均衡为在充电状态下,达到均衡条件,保护板开启均衡。静态均衡为在没有充放电电流的情况下,达到均衡条件,保护板开启均衡,静态均衡在电池压差较大时使用Checked for charg...
-
均衡功能-Balance function
开启或关闭保护板平衡各串电池电压功能,均衡功能原理是当单串电池间的电压达到设定压差时如0.03v,且电压高于设定开启电压,保护板判定达到均衡条件,如果开启的是充电均衡,则在充电时,达到上述条件,保护板开启均...
-
负载检测-Load detection
负载检测是指保护板在发生硬件过流及短路保护时,检测到负载则不释放,只有断开负载后,才能重新打开放电开关,以防止短路未解除时,打开放电开关对保护板造成损坏Load detection means that when the BMS is in...
-
开关功能-Switch function
保护板硬件功能,当有弱电开关时,勾选此选项。没有此功能不得开启,如开启,则保护板放电开关会关闭,保护板没有输出The BMS hardware function, check this option when there is a weak current switch. If ...
-
短路保护释放延时-Short circuit protection release delay
发生短路保护后,断开负载后,达到短路保护释放时间后,保护板打开放电开关,输出恢复正常After short-circuit protection occurs, after the load is disconnected, after the short-circuit protection release t...
-
硬件单体欠压延时-Hardware cell undervoltage delay
当单串电池电压到达硬件单体欠压保护电压,并且持续时间达到此设定时间时,保护板关断放电,发生欠压保护。When the cell battery voltage reaches the hardware unit undervoltage protection voltage and the dur...
-
硬件单体欠压-Hardware cell undervoltage
硬件单体欠压保护参数设置在前端检测芯片中,当保护板程序失效时,前端检测到电池电压达到硬件单体欠压时,前端芯片触发关断放电开关,关断后,只能通过主控芯片恢复正常后解除保护The hardware unit undervoltage ...
-
硬件单体过压保护延时-Hardware cell overvoltage protection delay
当单串电池电压到达硬件单体过压保护电压,并且持续时间达到此设定时间时,保护板关断充电,发生过压保护。When the cell battery voltage reaches the hardware unit overvoltage protection voltage and the dura...
-
硬件单体过压-Hardware cell overvoltage
硬件单体过压保护参数设置在前端检测芯片中,当保护板程序失效时,前端检测到电池电压达到硬件单体过压时,前端芯片触发关断充电开关,关断后,只能通过主控芯片恢复正常后解除保护The hardware cell over-voltage ...
-
短路保护延时-Short circuit protection delay
发生短路保护时,达到设置延时时间,保护板关闭输出,短路保护延时,与短路保护值关联起来设置,以达到即可以启动设备,又可以做到短路保护When short circuit protection occurs, the set delay time is reached, ...
-
短路保护电流-Short circuit protection current
电池组发生短路时,且短路电流达到保护电流时,保护板关断输出。短路电流需按电池实际短路值进行设置,不能过大,也不能过小,设置过大,短路达不到短路保护电流,保护板烧坏,设置过小,电池接上车时,会出现短路保...
-
硬件放电过流保护延时-Hardware discharge overcurrent protection delay
硬件放电过流保护是由前端检测芯片进行检测,当放电电流达到设定电流时,保护板关断放电开关,停止放电,以防止保护板、电池、及用电设备的损坏The hardware discharge overcurrent protection is detected by the ...
-
硬件放电过流保护-Hardware discharge overcurrent protection
硬件放电过流保护为前端检测芯片检测到电流大于硬件放电过流保护值时,保护板关断放电开关,停止放电,一般硬件过流值为额定电流的3-5倍The hardware discharge overcurrent protection is when the front-end dete...
-
充电过流延时-Charging overcurrent delay
电池组在充电时,充电电流超过充电过流保护值且达到充电过流延时时间,保护板关断充电开关,停止充电,以防止超功率使用When the PACK is charging, the charging current exceeds the charging overcurrent pr...
-
充电过流释放时间-Charging overcurrent release time
发生充电过流保护后,到达充电过流释放时间后,保护板重新打开充电开关After the charging overcurrent protection occurs, the BMS re-opens the charging switch after reaching the charging overcurrent rel...
-
充电过流-Charging overcurrent
电池组在充电时,充电电流超过充电过流保护值且边到充电过流延时时间,保护板关断充电开关,停止充电,以防止超功率使用When the PACK is charging, the charging current exceeds the charging overcurrent pr...
-
放电低温保护延时-Discharge under temperature protection delay
电池组在放电时,温度达到放电低温保护温度,并且持续达到放电低温保护延时时间,保护板关闭放电开关,停止放电,建议设置为5秒When the BMS is discharging, the temperature reaches the discharging under te...
-
放电低温保护释放温度-Discharge under temperature protection release
保护板发生放电低温保护后,当所有温度探头检测的温度都高于释放温度时,保护板重新打开放电开关,建议释放温度比放电低温保护温度高10度左右After the BMS is discharged and occured under temperature protec...
-
放电低温保护温度-Discharge under temperature protection
电池组在放电时,当温度低于放电低温保护温度时,保护板停止放电,以保护电池不受损伤,此参数需根据电池特性进行设置When the PACK is discharging, when the temperature is lower than the discharging low ...
-
放电高温保护延时-Discharge over temperature proctection delay
电池组在放电时,温度达到放电过温保护温度,并且持续达到放电高温保护延时时间,保护板关闭放电开关,停止放电,建议设置为2秒When the PACK is discharging, the temperature reaches the discharging over-t...
-
放电高温释放温度-Discharge over temperature protection release
保护板发生放电过温保护后,当所有温度探头检测的温度都低于释放温度时,保护板重新打开放电开关,建议释放温度比放电过温低15度左右After the BMS is overheated, when the temperature detected by all the te...
-
放电高温保护-Discharge over temperature protecion
电池组在放电时,当温控探头检测到温度到达放电过温保护温度,保护板关闭放电开关,停止放电,建议设置温度为75度When the PACK is discharging,the temperature control probe detects that the temperature r...
-
充电低温保护延时-Charging under temperature protection delay
电池组在充电时,温度达到充电低温保护温度,并且持续达到充电低温保护延时时间,保护板关闭充电开关,停止充电,建议设置为5秒When the BMS is charging, the temperature reaches the charging under temperat...
-
充电低温释放-Charging under temperature protection release
保护板发生充电低温保护后,当所有温度探头检测的温度都高于释放温度时,保护板重新打开充电开关,建议释放温度比充电低温保护温度高10度左右After the BMS is charged and occured under temperature protectio...
-
充电低温保护-Charging under temperature protection temperature
电池组在充电时,当温度低于充电低温保护温度时,保护板停止充电,以保护电池不受损伤,此参数需根据电池特性进行设置When the PACK is charging, when the temperature is lower than the charging low temper...
-
充电高温保护延时-Charging over temperature protection delay
电池组在充电时,温度达到充电过温保护温度,并且持续达到充电高温保护延时时间,保护板关闭充电开关,停止充电,建议设置为5秒When the PACK is charging, the temperature reaches the charging over-tempera...
-
充电高温释放温度-Charging over temperature protection release temperature
保护板发生充电过温保护后,当所有温度探头检测的温度都低于释放温度时,保护板重新打开充电开关,建议释放温度比充电过温低15度左右After the BMS is overheated, when the temperature detected by all the te...
-
充电高温保护-Charging over temperature protection
电池组在充电时,当温控探头检测到温度到达充电过温保护温度,保护板关闭充电开关,停止充电,建议设置温度为65度When the PACK is charging,the temperature control probe detects that the temperature reac...
-
整组欠压保护延时-PACK undervoltage protection delay
当电池组电压到达整组欠压保护电压时,持续时间达到整组欠压保护延时时间,保护板关闭放电开关When the PACK voltage reaches the PACK undervoltage protection voltage, the duration reaches the PAC...
-
整组欠压保护释放电压-PACK undervoltage protection release voltage
当电池组发生整组欠压保护后,当电池组恢复到释放电压时,保护板重新打开放电开关,电池组此时可以正常放电After the PACK occur PACK undervoltage protection, when the battery pack returns to t...
-
整组欠压保护-Pack undervoltage protection voltage
电池组整组低压保护电压,当保护板检测到电池组电压低于整组欠压保护电压时,保护板关闭放电开关,停止放电PACK under voltage protection voltage, when the BMS detects that the PACK voltage is lowe...
-
整组过压保护延时-Pack overvoltage protection delay
当整组电池电压到达整组过压保护电压时,持续时间达到整组过压延时时间,保护板充电开关关闭,停止充电。When the PACK voltage reaches the PACK set of overvoltage protection voltage, the duration re...
-
整组过压释放-PACK overvoltage release voltage
电池组发生整组过压保护后,当电压回落到整组电压释放值时,保护板打开充电开关。此值一般为电池串数*单体过压释放电压。After PACK overvoltage protection occurs in the battery pack, when the voltage fal...
-
整组过压-Pack overvoltage protection voltage
当电池组整体电压到达整组过压保护值时,保护板关闭充电开关,充电结束。在没有特殊要求的情况下,此值为电池串数*单体过压保护电压。When the PACK reaches the PACK overvoltage protection value, the B......
-
单体欠压保护延时-Cell undervoltage protection delay
当单串电池电压到达欠压保护电压,并且持续时间达到此设定时间时,保护板关断放电,发生欠压保护。此值推荐范围2-10秒,过小容易误触发保护,过长会使电池过放。When one cell battery voltage reaches the undervo...
-
单体欠压释放电压-Cell undervoltage release voltage
电池发生单体欠压保护后,当电压回升到单体欠压保护释放电压时,重新打开放电开关,释放值一般比单体欠压保护电压小0.3V。此值不得过大,充电时放电开关发热厉害,设过得过小在放电末端容易发生放电震荡。建议范围为......
-
单体欠压保护电压-Cell undervoltage protection
当单串电池电压达到单体欠压保护值时,保护板关闭放电开关,使得是池不能继续放电。When on cell battery reaches the value of the undervoltage protection voltage, the BMS closes the discharge switch, so...
-
单体过压保护延时-Cell overvoltage protection delay
当单串电池电压到达过压保护电压,并且持续时间达到此设定时间时,保护板关断充电,发生过压保护。此值推荐范围2-10秒,过小容易误触发保护,过长会使电池过充。When one cell voltage reaches the overvoltage pro...
-
单体过压释放电压-Cell overvoltage release voltage
电池发生单体过压保护后,当电压回落到此设定值,重新打开充电开关,释放值一般比单体过压值小0.1V。此值不得过大,过大时放电充电开关发热厉害。建议范围为小于过压值0.08-0.12V。如:三元设置为4.15V,铁锂设置为......
-
单体过压保护-Cell over voltage protection
单串电池电压到达设置保护电压后,保护板自动关断充电开关,以防止电池发生过充现象。After the single cell battery voltage reaches the set protection voltage, the BMS automatically turns off the chargi...
-
检流阻值-Current-sense resistance
检流阻值为保护板检测电流精密合金电阻阻值,此值硬件固定参数,不能修改。The current-sense resistance value is the protection plate detection current precision alloy resistance resistance value, this va...
-
标称容量-Nominal capacity
锂电池组实际组装容量值,请填写实际电池容量,此值会根据保护板实际学习容量,进行修正,最大修正比例为20%The actual assembled capacity value of the battery pack. This value will be corrected according t...